How to Equip the R&D Lab of a Company That Manufactures Adhesives and Sealants
By Cesare Strada, Sales Area Manager
The R&D laboratory of a company manufacturing adhesives and sealants needs equipment that operates in the same way as its production machinery, but on a smaller scale. The minimum essential setup includes a mixer using the same technology as the production plant and a system for discharging the product from the mixing vessel. Depending on the application, a second mixer and a raw material weighing system can also be added.
Why Is Laboratory Equipment Just as Important as Production Equipment?
Many chemical companies develop adhesives and sealants according to customer specifications or in response to increasingly demanding requirements for performance, sustainability, and efficiency. Every request starts in the laboratory: the product is formulated on a small scale, tested, and refined. Once approved, it moves on to full-scale industrial production.
Scaling up from laboratory to industrial production is a critical step. If the laboratory uses a different mixing principle from the production plant, the results achieved on a small scale may not be replicated in full-scale production. This often happens in companies that have invested in production machinery but only equipped their laboratories at a later stage, using generic equipment that was not specifically designed for the intended application.
The choice of laboratory mixer depends on the technology used in production.
What Equipment Is Needed in an Adhesives and Sealants Laboratory?
- A mixer using the same technology as the production equipment. The single-shaft high-speed disperser operates at high speeds and is used to disperse fillers and pigments in medium- to low-viscosity products. The dual-shaft disperser mixer combines a slow-speed butterfly agitator with a high-speed disperser, making it suitable for medium- to high-viscosity products. The laboratory version should be a scaled-down replica of the industrial machine, reproducing the same mixing principles as faithfully as possible!
- A mixing vessel that accompanies the product from start to finish. The entire mixing process takes place in the same vessel, which then moves on to the next stage without requiring any product transfer between mixing and discharge.
- An extruder for product discharge. When working with viscous products, emptying the mixing vessel is a process in itself. A laboratory extruder pushes the product out of the vessel and fills containers with a capacity similar to that of the vessel.
- Temperature Control. A jacketed mixing vessel, connected to the chiller already installed in the laboratory, maintains the product temperature between 0 and 50 °C, depending on the chiller’s performance.
- Raw Material Weighing as an Option. A dosing scale integrated into the same workbench incorporates raw material weighing into the process and ensures full batch traceability from start to finish, from raw material weighing to the finished product.
- Process Supervision Software. With an integrated workstation, all machines are connected to a central control PC that collects and stores all experimental data from each mixing process in a database. Every trial is fully traceable and can be monitored, while the collected data provides the foundation for scale-up when the formulation moves to industrial production.
How Is a Formulation Tested Before Moving to Production?
There are four possible approaches, depending on how frequently new formulations are developed and how closely the trials need to replicate industrial-scale production. The volumes indicated are those available at Zanelli’s Test Center, located at its headquarters in Collecchio, Parma (Italy).
| Where Testing Takes Place | Volume | When It Makes Sense |
| Benchtop dissipator, at the manufacturer’s test facility | 1–5 L | We want to test a formula before making any investment |
| Pilot plant with a turbo-disperser or a twin-shaft disperser-mixer | 270-liter tub | We need a batch on a scale close to that of production |
| Planetary pilot plant | 60-liter tub | This product requires planetary technology, which is typically used for higher viscosities |
| Laboratory bench at the company | 5 L effective (7 L geometric) | Development is an ongoing process: new formulas tailored to customer specifications, to be tested and replicated in-house |
The first three paths are for making decisions. The fourth is for working every day.
When is a full-size lab bench not necessary?
A complete unit, with a mixer and extruder mounted on the same base, is not necessary in every case.
- If the company is small and does not have a fully equipped laboratory. The workbench is designed for established companies with an R&D department that continuously develops formulas.
- If the tests are occasional. In this case, it makes more sense to test the formula at a testing facility, on a bench-top disperser, or on a pilot plant.
- If the lab is missing just one machine. The mixer and the extruder can also be purchased separately.
A complete workbench makes sense when the lab conducts development work every day and needs to remain consistent with the production machines.
Frequently Asked Questions
They are all the more representative the more the laboratory machine is a scaled-down version of the industrial model, with the same characteristics: the same type of shaft, the same mixing principle. A generic laboratory mixer does not offer the same level of correspondence.
Yes. The mixer and the extruder can also be purchased separately. The complete workstation is recommended when you want a compact unit with all the stages in one place.
In the configuration described here, the tank has a geometric capacity of 7 liters, 5 of which are usable for mixing. This volume is intended for formula development, not for production.
No. It’s not a permanent installation: you can move it around within the lab or department, depending on how you organize your work.
An example: the laboratory of an adhesive manufacturer
A chemical company that manufactures adhesives already had production machinery, but its laboratory lacked equipment that was scalable and complementary to the plant’s machinery. Zanelli therefore designed a custom-built unit: a single-shaft turbodisperser and an extruder mounted on the same base, with overall dimensions of 1,208 × 2,100 mm.
The product is mixed in a 7-liter tank with a thermostatically controlled jacket. At the end of the cycle, the tank moves on a slide to the extruder, which fills the jars. The mixer is controlled via a touchscreen panel.
This bench is a Smart Lab Mixing Unit by Zanelli, and the one in the case study is just one of the possible configurations. The modules are selected based on the customer’s process. For high-viscosity adhesives and sealants, as in this case, a mixer and an extruder are required.
For more fluid products, such as paints, varnishes, and coatings, the station can be configured with two mixers—for example, a single-shaft turbo disperser and a twin-shaft mixer-disperser. In both cases, the station can be equipped with systems for controlling the dosing and tracking of raw materials, such as a dosing scale. The goal is full traceability and quality control starting from the prototyping phase.
The workbench can be moved around the lab or department, depending on how the work is organized.